Produkty dla konstrukcja wierzchnia (17)

Syntech Pavicrom SBV Colored two-component finish, permeable to water vapour, based on epoxy resins in water dispersion. Ideal for the pigmented coating of industrial floors and concrete constructions in general with residual humidity and without vapor barrier. Surfaces treated with Syntech Pavicrom SBV are easy to clean and guarantee excellent resistance to mechanical wear, as well as being highly resistant to water, alkaline solutions, detergents and hydrocarbons (petroleum, diesel, petrol, etc.) . Protective and decorative painting of concrete floors, restoration of the color of old resin floors, glazing of wall skirting boards, etc. Ideal for mechanical workshops, manufacturing industries, warehouses and factories in general where high chemical and mechanical resistance is required. It can be used both indoors and outdoors. Concrete The surfaces to be coated must be stable, clean and free of substances that could affect the adhesion of the coating. In case of restoration, use suitable mortars and products suitable for the system beforehand. Wait for the drying times before applying the next coat. The tensile strength must not be less than 1.5 N/mm². Existing paints, coatings or paints, cement grout residues, release agents, oils, greases, silicones, etc. they can be removed mechanically by sandblasting, blasting, hydroblasting or chemical removal. Cracks and fissures In case of static cracks, use Syntech Primer EP-W for sealing. The sealing of dynamic cracks or cracks larger than 4-5 mm must be assessed on site. Generally they can be grouted with elastomeric materials or act as expansion joints. Grouting and spot repairs Any holes or repairs to portions of concrete can be made with mortars from the REPAR line or by applying epoxy mortar made with Syntech Primer EP-W and quartz mastics. Apply a coat of Syntech Primer EP-W as a bonding primer, then proceed to seal and repair the damaged and broken concrete by applying the epoxy mortar. Any small filling of holes and cracks can be done by applying Syntech AS 21 epoxy mortar. Resin coatings The surfaces to be covered must be stable, clean and free of substances such as dirt, grease, oil, etc. which can affect the adhesion of the coating. Smooth the surface by mechanical sanding with diamond discs and vacuum. It is recommended to wash the surfaces and let them dry completely before applying the finish. Primer for concrete Syntech Pavicrom SBV can be applied directly to cementitious substrates as the product diluted with a maximum of 25% by weight of clean water acts as an anchoring primer. Resin coatings The application of Syntech Pavicrom SBV on resinous and multilayer systems must always be preceded by sanding the entire surface to promote and guarantee optimal adhesion of the product to the support. Combine the two components in the indicated mixing ratio. Add component B (hardener) to component A (base) and mix well until a completely homogeneous product is obtained. It is advisable to start mixing briefly with an electric drill at low speed and then intensify the stirring up to a maximum of 300-400 rpm. Leave the emulsion obtained to rest in the container, respecting the following induction times: at 15°C ~ 20 minutes at 25°C ~ 15 minutes at 30°C ~ 10 minutes The product can be applied uniformly using a spray gun or short-haired roller to avoid accumulations of material which could give rise to aesthetic defects. The application of the product must be carried out by crossing the passes and paying particular attention to the shots, regularly unloading the roller beyond the applied area to obtain a uniform film and eliminate any accumulations of product. Apply the first coat of Syntech Pavicrom SBV diluted with a maximum of 25% by weight of clean water as primer. The dilution must be carried out under mechanical stirring, adding the necessary quantity of water at the end of the induction time. Do not dilute the product further during application if it thickens it means that the use time has expired. Create a new emulsion with highly mixed material. Wait at least 12 hours, then apply the second one Colored finish diluted with a maximum of 20% weight of clean water, respecting the consumption and thicknesses indicated. It is possible to create non-slip finishes by adding quartz or hollow glass spheres. From 0.15 to 0.20 kg of Syntech Pavicrom SBV for each square meter of surface to be covered, for each coat. Pail 2.5 kg [A] - Pail 5 kg [A] - Pail 3 kg [B] - Pail 6 kg [B] - Kit: 1 Pail 2.5 kg [A] + 1 Pail 3 kg [B] - Kit: 1 Pail 5 kg [A] + 1 Pail 6 kg [B]

Bei Bodenprojekten setzen wir auf eine enge Zusammenarbeit mit unseren Kunden und eine detaillierte Analyse der Gegebenheiten vor Ort, um Ihre Vorstellungen optimal zu verwirklichen. Unsere jahrelange Erfahrung hilft uns dabei mögliche Probleme zu erkennen und eine perfekte Lösung für jedes Bauvorhaben zu finden. Bodenbeschichtungen: Um eine hohe Qualität sicherzustellen, verwenden wir bei unseren Bodenbeschichtungen nur sorgfältig ausgewählte Materialien, welche eine hohe Beständigkeit und Verschleißresistenz aufweisen. Beim Verlegen setzten wir besonders auf eine fugenlose Verarbeitung, wodurch unsere Böden jeglichen hygienischen Ansprüchen gerecht werden.

surface protection for concrete, crack filling, hydrophobic impregnation

Large gamme de moquette de protection pour chantiers (nous consulter)

Flächenheizelemente werden in vielen industriellen Anwendungen eingesetzt. Häufig in Verpackungsmaschinen, Extrudern, Maschinenbau usw.

Mit der großen Flächenschleifmaschine / Bandschleifmaschine (Hummel) werden Flächen größer als 30m² geschliffen. Unser Flächenschleifer zeichnet sich durch die leichte Bedienbarkeit und hohe Schleifleistung aus. Er verfügt über eine eigene Staubabsaugung. Gewicht ca. 80kg. Verwendbar für: Parkett, Dielenboden Tagesmietpreis: 49,00 €

Nemo Grabo handvacuumzuiger op accu is de musthave voor iedere vakman die regelmatig moet tillen. Nemo grabo is de eerste elektrische draagbare vacuümzuiger die zich hecht op bijna alle soorten oppervlakken. Zelfs materiaal met structuur, reliëf of oneffenheden zijn op eenvoudige wijze te tillen. Zo kunnen de elektrische handvacuümzuigers gebruikt worden om o.a. hout, metaal, glas, natuursteen of kunststof aan te zuigen. Deze krachtige tool minimaliseert het risico op schade aan dure materialen en maximaliseert de efficiëntie en dat terwijl de fysieke belasting wordt verminderd. Grabo is een nieuw gepatenteerd product dat is ontwikkeld door Nemo Power Tools. Een nieuwe en revolutionaire manier om bijv. glas/tegels/beton/hout te kunnen tillen. Ontwikkeld voor vloerenleggers, tegelzetters, verhuizers, glaszetters, interieurbouwers, installateurs en nog vele andere professionals. Bij Werkplaatstechniek koop je de Nemo grabo plus, Pro in tas of systainer.

VinyTherm® steenstrips voor buiten waar echt natuursteen in het oppervlak is ingesmolten, de toplaag is van echt natuursteen. VinyTherm steenlook gevelbekleding is leverbaar als vlakke afwerking of met voeg. Hierdoor sluiten ze beter op elkaar aan en ziet de gevel er als een geheel uit. VinyTherm® steenslag panelen worden veelal gebruikt voor renovatieprojecten waar een natuursteen uitstraling gewenst in. Deze kunststof panelen met natuursteen steenstrips worden gefabriceerd in lange panelen voor eenvoudige montage. De steenstrips panelen voor de gevel zijn duurzaam en milieuvriendelijk, UV bestendig en vochtbestendig. VinyTherm gevelbekleding verleent zich uitstekend voor renovatieprojecten waar een natuursteen uitstraling gewenst is, denk hierbij aan bijvoorbeeld gevels en balkonbekleding. Gevelpaneel vlakke afwerking: Lengtes tot 6 meter x 203 x 24 mm werkend: 180 mm

Syntech RGS A fluid, medium-viscous epoxy adhesive for the structural casting of joints (new conglomerates on existing structures). After careful mixing, the two-component compound must be applied on the existing concrete by brush or roller, a few minutes before applying the new conglomerate (“wet-on-wet”). Construction joints between new and existing concrete, flooring and structures. Sealing and filling of cracks in the concrete (of a magnitude greater than 1 mm). The application surfaces should be suitably prepared and adequately resistant: free from dust, grease, fouling, crumbling and non-adhering parts, free of detected surface humidity, for floorings, moreover, it may be advisable to carry out preliminary shot peening or milling of adhesive surfaces. Add component B to component A taking care to remove all the material from the packaging, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mixture is obtained; add the required load amount (component C) continue to mix until a homogeneous lump-free mixture is obtained. Apply by brush or roller on the surfaces prepared. Spread, or "cast" on site, the subsequent conglomerate, in the range of application defined by the conditions of adherence of Syntech RGS (before it hardens). Apply from 0.30 to 1,00 kg of Syntech RGS per square metre of surface to be treated. Can 3.3 kg [A] - Can 13.4 kg [A] - Can 1.7 kg [B] - Can 6.6 kg [B] - Kit: 1 Can 3.3 kg [A] + 1 Can 1.7 kg [B] - Kit: 1 Can 13.4 kg [A] + 1 Can 6.6 kg [B]

Liquid product based on lithium silicates, which was created for the protective, consolidating and porosity reducer treatment of concrete, mineral, brick and stone substrates. It guarantees optimal durability and adhesion strength, resistance to UV rays, chemical agents and mechanical stresses. The result of the application allows to obtain a rapid hardening of the surface as well as a revived and homogeneous appearance of the same. The product has a negligible environmental impact thanks to the low VOC content (<50 g / l) and is practically odorless. Protective, reinforcing, water repellent treatments of concrete, mineral and stone supports. Specific product for revitalizing, simultaneously providing a great consolidation and an annulment of the dust produced in concrete supports, interstices, brick, stone or mixed arches, present in taverns, public premises and of historic monuments interest. The application surfaces should be clean, free of incrustations, dust etc. A preliminary wash with distilled water or steam it's recommended. The support should be dry when applying. Apply the product as it is, with low pressure sprayer or brush with long bristles. Keep the substrate wet with Consilex Idrofix for at least 20 minutes during application. If applied on floors, wait 24 hours before passing on the treated support. The reinforcing contribution will be completed after 2-3 weeks of treatment. From 0,20 to 1,00 kg of Consilex Idrofix per square meter of surface to be treated, based on the porosity of the support.

An anti-dust chemical/mechanical revitalising hardener for concrete flooring and screeds, consisting of an aqueous solution of mineral silicates and fluosilicates, activated by specific wetting agents. It is applied in several coats of decreasing dilution in water, with a brush or mechanical “scrubber”. Specific anti-dust treatments for industrial flooring or concrete slabs that have lost their original “vitality”. It reacts with the calcium compounds, soluble and unstable, present in of concrete products, transforming them into new stable, insoluble and resistant compounds. Consequent increases in resistance to wear and tear of the order of 200% -400%, significant increases in chemical stability, resistance to freeze-thaw cycles etc. Reactive impregnations for stabilising chemical and mechanical structures and concrete products. Hardening, anti-dust, anti abrasive and anti-corrosion treatments for concrete floorings. Adjustment of the chemical and mechanical performance of products for the industrial, rural and livestock construction (on horizontal surfaces). Apply, preferably with a brush or with "washer dryer" machine on the basis of the following indications: - Porous surfaces: repeated applications of a solution of water and QL Fluosil at a ratio in 1:1 - Compact surfaces: apply three coats, with decreasing dilution with water. 1a coat 1:3, 2a coat 1:2, 3a coat 1:1. The consumption of QL Fluosil will be proportional to the absorption of the floor to be treated. Indicatively a porous surface will consume about 400 g/m², while a surface with normal porosity will consume 250-300 g/m². Leave the product to dry between one coat and the next and then, after the last coat, wash with copious amounts of water. Protect glass and aluminium surfaces during application. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface".

surface protection for concrete, crack filling, hydrophobic impregnation

surface protection for concrete, crack filling, hydrophobic impregnation

surface protection for concrete, crack filling, hydrophobic impregnation

surface protection for concrete, crack filling, hydrophobic impregnation

very fast curing, high flexibel, abrasion and UV stable surface protection for concrete

surface protection for concrete, crack filling, hydrophobic impregnation